# 6.3.1.1. Main¶

## 6.3.1.1.1. Site URL¶

Write the base URL of the site.

Base URL
Target site’s URL that consists of its domain. E.g. https://wordpress.org/. Do not include the parts other than the domain. For example, instead of https://wordpress.org/plugins/, write https://wordpress.org/. The URL must start with http.

Important

You must fill this field.

Important

The value entered here will be used to make relative URLs full URLs when there is a need. Therefore, if this URL is not the base URL, then your relative URLs defined throughout the settings will not work.

## 6.3.1.1.2. Active for scheduling?¶

Check this setting’s checkbox if you want to enable automatic URL collection and post crawling for this site. For automatic crawling to be enabled, you must also enable scheduling under the general settings of the plugin (See: Scheduling is active?).

## 6.3.1.1.3. Active for recrawling?¶

Check this setting’s checkbox if you want the posts that are saved by using this site’s settings to be updated. For automatic recrawling to be enabled, you must also enable recrawling under the general settings of the plugin (See: Recrawling is active?).

## 6.3.1.1.4. Active for post deleting?¶

Check this setting’s checkbox if you want the posts that are saved by using this site’s settings to be deleted. For automatic deleting to be enabled, you must also enable deleting under the general settings of the plugin (See Deleting is active?).

## 6.3.1.1.5. Active for post translation?¶

Check this setting’s checkbox if you want the posts that are saved by using this site’s settings to be translated. For automatic translation to be enabled, you must also enable translation under the general settings of the plugin (See Translation is active?) and configure translation settings.

## 6.3.1.1.6. Translatable Fields¶

You can select which fields should be translated. If you select none, it means all fields are translatable. The list of translatable fields can be seen in Transformable Fields.

Note

This setting is visible only if Active for post translation? setting is enabled.

Important

The fields are translated after the templates are prepared. So, if a translatable field is used in a non-translatable field via short codes, value of the translatable field is included into the non-translatable field without translation.

## 6.3.1.1.7. Active for post spinning?¶

Check this setting’s checkbox if you want the posts that are saved by using this site’s settings to be spun. For automatic spinning to be enabled, you must also enable spinning under the general settings of the plugin (See Spinning is active?) and configure spinning settings.

## 6.3.1.1.8. Spinnable Fields¶

You can select which fields should be spun. If you select none, it means all fields are spinnable. The list of spinnable fields can be seen in Transformable Fields.

Note

This setting is visible only if Active for post spinning? setting is enabled.

Important

The fields are spun after the templates are prepared. So, if a spinnable field is used in a non-spinnable field via short codes, value of the spinnable field is included into the non-spinnable field without spinning.

## 6.3.1.1.9. Check duplicate posts via¶

Set how the plugin should decide if whether a post is duplicate or not. Duplicate checking will be performed in this order: URL, title, content. If one of them is found, the post is considered as duplicate.

The duplicate check types are as follows.

URL

If the same URL already exists in the database, then the post is duplicate. Do not save it.

Note

The same URL cannot be inserted into the database, by design. So, no matter you select this or not, the same URL will not be crawled again.

Title
If a post, that was saved by the plugin, with the same title exists, then the post is duplicate. Do not save it.
Content
If a post, that was saved by the plugin, with the same content exists, then the post is duplicate. Do not save it.

## 6.3.1.1.10. Use custom general settings?¶

Check this setting to override general settings. When this checkbox is checked, Settings tab will become visible. You can override the general settings from Settings Tab.

Important

When this checkbox is checked, all of the general settings will be overridden, except for certain few settings (See: Settings Tab). Hence, if you leave a setting that is under Settings tab empty, it is still overridden. In other words, leaving a setting empty does not mean “do not override”.